Oct 23, 2012 · John: Welcome to Just Answer! John: To setup the Dlink DIR-605L as an access point, please follow the instructions below. John: If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: • Disable UPnP™ • Disable DHCP • Change the LAN IP address to an
Nov 05, 2009 · Well I was able to configure the Dir-615 in Wireless Access Point and also to set my port-forwarding in the EQ-660 router. For the port-forwarding, I am trying to use 2 ports: 3389 and another one I specified in the xx,xxxx range, which the Host is set to listen, as configured in IIS services in the Host machine. To get to the configuration page for the access point, you need to know the access point’s IP address. Then, you just type that address into the address bar of a browser from any computer on the network. Multifunction access points usually provide DHCP and NAT services for the networks and double as the network’s gateway router. I thought the DIR 615 would just work as a router if I plugged it into the HH5. And turn off DHCP server. If I factory reset DIR 615 DDWRT, can you guide me through setting it up as an access point for LAN whilst its connected to my HH5? Oct 23, 2012 · John: Welcome to Just Answer! John: To setup the Dlink DIR-605L as an access point, please follow the instructions below. John: If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: • Disable UPnP™ • Disable DHCP • Change the LAN IP address to an Jan 19, 2009 · Creating a Wireless Access Point using DD-WRT - Refresh 19 January 2009 on DD-WRT, How To, Linksys, Tomato, WRT150N, WRT54G. I found a setup that I like even better than my previous one. I have highlighted the main differences, in red, below. To set it up as repeater do the following: Do a 30 second reset; Under wireless->basic settings
How to setup D-Link DIR-615 Wireless Router as switch How to setup D-Link DIR-615 Wireless Router as switch 1. Login D-Link Wireless Router. 2. Navigate to Setup>Internet>WAN. 3. Make sure the Internet connection type is DHCP. 4. In the Network settings, setup the Router IP and subnet. 5.
May 15, 2014 · With the DHCP server turned off, the access point needs to be able to connect to the network, so we need to assign a fixed ip address that the access point will always use. This contrasts with the dynamically allocated ip addresses that the other network connections will be given by the DHCP server in the router. • Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DIR-615 wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless router. View full D-Link DIR-615 Wireless N Router specs on CNET.
I thought the DIR 615 would just work as a router if I plugged it into the HH5. And turn off DHCP server. If I factory reset DIR 615 DDWRT, can you guide me through setting it up as an access point for LAN whilst its connected to my HH5?
I have a DIR-615 Wireless router, that being used as an access point. It been working perfect for the last 2 yrs. Over the last 2 weeks, it started acting odd. Jun 04, 2012 · 10) Voila! You now have a wireless access point. I tested it out by disabling my wireless on my primary router and… WOOT! we still have wireless access (through the D-Link router). You can also type “192.168.1.253” to any computer that is connected to your LAN in order to access your D-Link router settings.